气液结合增压特点特点：
速度快：动作速度较液压传动快，且较气压传动稳定；
易使用：缸体装置简单，出力调整容易，使用保养方便；
出力大：在相同途径条件下可达油压机之高出力，非纯气压系统可达到；
价格低：设备单价较油压系统低廉；
易维护：因结构简单，故维护较油压系统简便；
能耗低：持续加压或停止动作时，不必像纯液压系统那样，马达需持续运转，故可节省能源，且动力来源方便易取，实际能耗相当于油压系统10%-30%；
无泄漏：能量转换方便，可以做到零泄漏不必担心环境污染；
不损模：为适应工艺需要，冲压力和工作行程在规定范围内可达到无极可调；
安装易：多种安装方式，根据不同工作场合可在任意角度位置安装；
软着陆：冲压软到位技术，使作动时噪音小及保护您的模具；
故障少：无油压系统温升之困扰；
空间小：与普通气缸及液压站相比，占用空间面积可小于50%以上；
Product features:
fast speed: the speed is hydraulic drive fast, and more pressure stable transmission;
easy to use: cylinder device has the advantages of simple structure, easy adjustment for output, convenient use and maintenance;
output: in high output up to press the same way conditions, non pure pneumatic system can achieve;
low prices: equipment at a hydraulic system low;
easy maintenance: because of its simple structure, the hydraulic system maintenance is simple;
low energy consumption: continuous pressure or stop the action, not as pure as the motor to hydraulic system, continuous operation, so the energy can be saved, and the power source is easy to take, the actual energy consumption is equivalent to the hydraulic system of 10%-30%;
no leakage: energy conversion is convenient, can achieve zero leakage do not have to worry about environmental pollution;
loss model: in order to meet the process requirements, pressure and stroke work within the prescribed scope can achieve stepless adjustable;
easy installation: installation method, according to the different working conditions can be installed at any angle position;
soft landing: soft in place of stamping technique the die when moving, low noise and protect your;
less failure: no hydraulic system temperature rise of distress;
small space: compared with ordinary cylinder and the hydraulic station, the space occupation Area of less than 50%;

产品注意事项：
由于增压缸经常处于高速运转状态，容易造成机器磨损，所以应按操作说明书来作业，增压缸的工作温度在-5℃~60℃左右，操作速度50~1000mm/s，为了保证增压缸的正常工作，使用中应注意以下几点：
1.保持清洁。
在将增压缸接入气路前，敬请先将管路及元件内的灰尘等杂物清除，以免降低增压缸的使用寿命。
2.正常气压范围内使用。
缸在正常使用时工作气压须要按照检验报告中规定的工作气压范围内工作，不得超过规定的工作压力.。
3.注意增压缸的工作环境。
缸在设计时工作环境内的温度已定，若因工作需要变换工作环境超过温度需与增压缸技术相关人员联系处。由于缸中的部分元件为铁质，所以请不要将其置于工况环境特为复杂的环境内使用(如有化学物质的接触环境)，另请在缸前端加装有效的空气处理元件(三点组合)并接时加油润滑及排水处理。
4.不可擅改加其它液压油。
增压缸在设计时所选用的液压油价质为VG68#抗磨液压油，不可撤擅自改用其它液体介质(如机油.水等)。
5.一定要按程序操作。
动作程序一定要按照气路配装图的动作程序工作即预压动作-增压动作增压释压-预压复位。
6.注意保养，经常检查增压缸运转。
为避免缸在增压时动作的压力过大破坏您的模具或工件，敬请在增压段进入口处加装一减压阀,以便能有效保护您的产品。为确保增压缸工作的稳定性，建议尽可能在三联件与增压缸之间并联加装一储气筒。
使用增压缸500000次以上或半年以上时，建议将缸中的液压油全部更换一次，以提高缸的使用寿命和工作年限。
Note:
because the pressurization cylinder often operates at high speed, easy to cause the machine wear, so should according to the operating instructions to operation, pressurized cylinder working temperature -5 ℃ ~60 ℃, the operation speed of 50~1000mm/s, in order to guarantee the normal work of the pressurizing cylinder, should pay attention to the following points:
1.the use of clean.
The pressure cylinder access gas path before, please first line and components of dust and other debris removal, so as not to reduce the service life of the pressurizing cylinder.
2.normal pressure range use.
Cylinder working in normal use pressure must work in accordance with the working pressure range specified in the test report, shall not exceed the prescribed work pressure.
3.note pressure cylinder working environment.
Cylinder in the design time environment within the temperature is fixed, if need because of the job transform working environment temperature and pressure cylinder over related technical personnel office. Because the component cylinder is iron, so please do not use it under the conditions for complex environment (such as exposure to environmental chemicals), please air handling units installed in front of effective cylinder (three points) and joint lubrication and drainage treatment.
4.can not be repeated and other hydraulic oil.
Hydraulic oil pressure cylinder in the design quality for the selected VG68# anti-wear hydraulic oil, can not be removed or switch to other liquid medium (such as oil. Water etc.).
5.we must operate according to the procedure.
Action program must be in accordance with the pneumatic loading diagram of the action program of work pressure action - pressurization action supercharging pressure release and pre press reset.
6.pay attention to maintenance, often check the pressure cylinder operation.
To avoid pressure cylinder in boosting the excessive damage your mold or workpiece, please in the booster section into the mouth is provided with a pressure relief valve, so that it can effectively protect your products. In order to ensure the stability of pressure cylinder work, suggestions as far as possible in the triplet and the pressurizing cylinder equipped with a parallel between the air storage reservoir.
The use of the pressurizing cylinder is more than 500000 times or more than half a year, suggested that hydraulic cylinder of all change, in order to improve the service life of the cylinder and working life.